Why Learning Plumbing Basics is Essential for Installing a Bathtub
Why Learning Plumbing Basics is Essential for Installing a Bathtub
Blog Article
The writer is making a few good points about A Step-by-Step Guide to Installing a Bathtub overall in this content on the next paragraphs.
Setting up a bath tub isn't exactly rocket science, but it does require solid plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old tub with a new one is also a reasonably difficult task. If the old bathtub is easily obtainable, the task can relocate immediately; if you have to open up a wall surface to get rid of the old tub and place the new bathtub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have qualified on your own for the task and fit attempting it. Instead of working with a service provider to take over a halfway-completed task, it is far better to think about utilizing one before you begin. Opportunities are you might require a specialist plumber to make tube links.
This post will aid you set up a brand-new bath tub in your bathroom if you have already purchased a new tub and do not require to alter the arrangement of your previous supply of water pipes.
Your tools as well as product checklist ought to consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, turn on the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be rather troublesome because of the limited access that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a cloth prepared for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers remain in place in between the tap as well as the sink. Safeguard the faucet in position with the producer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous type must be attached to the tap finishes first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing the two wood boards under its feet, position the tub in the needed placement. The wood boards are helpful in equally spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the tub up until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression join; then do the very same for the various other faucet.
Activate the water and examine all joints and new pipework for leaks and tighten them if essential. Fill up the bath tub and additionally check the overflow outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling and sealing around the bathtub ought to wait until the bathtub has actually been made use of at least once as this will resolve it right into its last setting.
Planning for the Installation
To start with, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps unit to avoid strain on the bathtub.
Fit the adaptable tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath should currently be ready to be fitted in its final placement.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to split a rigid seal, triggering the water to penetrate the wall in between the bath as well as the tiling, resulting in complications with moisture and possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and fittings. They are offered in tubes and cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the tub with water prior to sealing, to allow for the activity experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the market. It is suggested to fit the floor tiles using waterproof or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our excerpt about How to Install a Bathtub Yourself. Thanks so much for spending some time to read through our piece of content. Do you know somebody who is curious about the subject? Take a moment to promote it. We take joy in reading our article about How to Install a Bathtub Yourself.
Effective fix? Call! Report this page